Do not treat a reactor name or daily capacity as a complete project specification.
ចំណី, preparation, operating continuity, condensation, gas safety, product handling, ការត្រួតពិនិត្យបរិស្ថាន, utilities and local delivery scope must be configured together.
Approved small-scale reference
YSX-F1 to YSX-F5 denote 1, 2, 3, 4 និង 5 t/day skid or modular planning references for tire, plastic or oily-sludge trials.
Material balance
Oil, ឧស្ម័ន, solids and metal-bearing outputs require representative feedstock, stable-run data and an agreed sampling boundary.
Commercial boundary
Prices, operating costs, product value and return require dated quotations and local market evidence.
Source control: approved YOTO group product register. Final parameters are issued on the project-specific technical agreement.
The HTP-1000 name is retained as a project reference. លំហូរមានស្ថេរភាព, dryer duty, reactor configuration, gas treatment, controls and price require representative sludge analysis and a written quotation.
ប្រព័ន្ធនេះមានសមត្ថភាពផលិតប្រចាំឆ្នាំប្រហែល 2,000 ធ្យូង pyrolytic រាប់តោន, ដែលមានតម្លៃទីផ្សារសំខាន់. លើសពីនេះទៀត។, តាមរយៈការស្តារថាមពល និងដំណើរការជួសជុលកាបូន, វាកាត់បន្ថយ កាបូនឌីអុកស៊ីត ការបំភាយឧស្ម័នដោយប្រហែល 1,500 តោនជារៀងរាល់ឆ្នាំ, ដែលសម្រេចបាននូវគោលដៅនៃការសម្របសម្រួលអេកូឡូស៊ី និងសេដ្ឋកិច្ច.
តើអ្វីជាភាពខុសគ្នានៃប្រសិទ្ធភាពរវាងប្រព័ន្ធ pyrolysis បន្ត និងអន្តរកាល?
នៅក្នុងដំណោះស្រាយ pyrolysis សម្រាប់គម្រោងព្យាបាល sludge ទីក្រុង, ផ្លូវដំណើរការ pyrolysis ផ្សេងគ្នាប៉ះពាល់ដល់ប្រសិទ្ធភាពប្រតិបត្តិការ និងគុណភាពផលិតផលដោយផ្ទាល់. ក្នុងចំណោមទាំងនេះ, ប្រព័ន្ធ pyrolysis បន្តនិងជាបាច់តំណាងឱ្យរបៀបប្រតិបត្តិការធម្មតាពីរ, នីមួយៗមានលក្ខណៈបច្ចេកទេសតែមួយគត់ និងសេណារីយ៉ូដែលអាចអនុវត្តបាន។.
Drilling waste, tank-bottom sludge, refinery sludge and marine oily residues differ in water, សារធាតុរឹង, hydrocarbons, salt, sulfur and metals. They should not share an assumed standard configuration.
Follow the material, vapor, រាវ, gas and solid paths
The reactor is one part of the line. Commercial operability depends on how each stream is prepared, transferred, controlled and discharged.
- 01Material characterization
- 02Feed preparation and sealed transfer
- 03Controlled thermal conversion
- 04Vapor separation and staged condensation
- 05Non-condensable gas safety and reuse
- 06Solid cooling, discharge and product handling
Configuration questions that change the proposal
The following points should be resolved before selecting a capacity or preparing a commercial quotation.
Conditioning and dewatering
High water content changes feeding stability and energy demand; pumping, mixing, dewatering or screw feeding may be required.
Fouling and corrosion
Salt, fine solids and heavy fractions influence reactor cleaning, metallurgy and condensation-system maintenance.
Recovered phases
Separate the project basis for recovered oil, water and treated solids, including sampling and permitted downstream use.
Hazardous-waste boundary
Licensing, residue classification, worker protection and emissions monitoring must be defined for the project jurisdiction.
Make utilities and product outlets visible before investment
A useful feasibility review connects the mass balance, energy balance, operating schedule and local product route.
Operating schedule
Define planned hours per day, shutdown windows, cleaning strategy, labor model and feedstock storage capacity.
Energy integration
Evaluate non-condensable gas reuse, startup fuel, electrical loads, cooling demand and optional downstream energy use as one balance.
Quality control
Set sampling points for incoming material, condensate fractions, recovered solids, wastewater and exhaust gas.
Commercial boundary
Budgetary results remain conditional until the feedstock, គេហទំព័រ, product route and local compliance requirements are confirmed.
See the connected equipment boundary.
Reference visuals support early layout discussion. Final equipment, arrangement and interfaces are confirmed from the project material and site.
បកប្រែការពិតគម្រោងទៅក្នុងបញ្ជីឧបករណ៍.
ម៉ាទ្រីសយោងនេះបង្ហាញពីតក្កវិជ្ជានៃការសម្រេចចិត្ត. បរិមាណចុងក្រោយ, ម៉ូដែល និងចំណុចប្រទាក់ជាកម្មសិទ្ធិនៅក្នុងសំណើគម្រោងដែលបានអនុម័ត.
| ប្លុកប្រព័ន្ធ | វិសាលភាពធម្មតា។ | មូលដ្ឋាននៃការកំណត់រចនាសម្ព័ន្ធ |
|---|---|---|
| Receiving and conditioning | Sampling, mixing, ការពិនិត្យ, dewatering or pumpable-feed preparation | Water, សារធាតុរឹង, salts and viscosity |
| Controlled feeding | Agitated buffer, pumps or screws, seals and isolation | Phase stability and hazardous-waste controls |
| Thermal treatment | Reactor, heating, fouling management and cleanout access | Hydrocarbon range, solids and corrosion basis |
| Phase recovery | Vapor separation, oil-water handling and treated-solid cooling | Sampling and permitted downstream routes |
| Environmental and residue | Gas treatment, wastewater, residue containment and monitoring | Local licensing and acceptance tests |
ជំរុញគម្រោង លុះត្រាតែមានភស្តុតាងចាំបាច់.
ច្រកនីមួយៗបង្វែរព័ត៌មានរបស់អតិថិជនទៅជាលទ្ធផលបច្ចេកទេស ឬពាណិជ្ជកម្មដែលបានកំណត់សម្រាប់ការសម្រេចចិត្តបន្ទាប់.
Waste characterization
Sample water, ប្រេង, សារធាតុរឹង, salts, ស្ពាន់ធ័រ, metals and hazardous properties.
ទិន្នផលRepresentative waste profileConditioning trial
Verify mixing, dewatering, pumping or screw-feeding requirements.
ទិន្នផលStable feed-preparation routeOutput controls
Define recovered phases, treated residue, wastewater and sampling methods.
ទិន្នផលPermitted output-management planFacility integration
Confirm licensing, containment, ឧបករណ៍ប្រើប្រាស់, monitoring and acceptance.
ទិន្នផលSite-specific technical boundaryសំណួរដែលត្រូវដោះស្រាយមុនពេលកំណត់រចនាសម្ព័ន្ធ.
ចម្លើយកំណត់ព្រំដែនវិស្វកម្ម; ពួកគេមិនជំនួសការធ្វើតេស្តសម្ភារៈតំណាង ឬការត្រួតពិនិត្យការអនុលោមតាមមូលដ្ឋានទេ។.
What determines the continuous pyrolysis equipment list?
Feedstock form, សមាសភាព, សំណើម, contamination, planned operating schedule, recovered-product route, site utilities and permit requirements determine the configuration.
Can tires, plastics and oily sludge use exactly the same line?
ទេ. They may share thermal-conversion principles, but their preparation, feeding, corrosion, condensation, solid handling and environmental controls differ materially.
Can recovered oil performance be guaranteed from a general material description?
ទេ. Representative analysis and an agreed sampling method are required before recovered-liquid quantity, quality or downstream use can be evaluated.
What should be included in acceptance testing?
Define feedstock, run duration, mass balance, operating stability, sampled outputs, ឧបករណ៍ប្រើប្រាស់, safety interlocks and the applicable emissions or residue tests.
កំណត់សម្ភារៈមុនពេលជ្រើសរើសឧបករណ៍.
ចែករំលែកការពិពណ៌នាសម្ភារៈតំណាង, កម្រិតសំឡេងដែលអាចប្រើបាន, ស្ថានភាពគេហទំព័រ និងលទ្ធផលគោលដៅ. YUSHUNXIN នឹងប្រើប្រាស់ការពិតទាំងនោះ ដើម្បីរៀបចំការពិភាក្សាអំពីព្រំដែន និងការកំណត់រចនាសម្ព័ន្ធដំណើរការពាក់ព័ន្ធ.
